CN
EN
The most complete and detailed installation steps of faucet
Time : 2021-10-10 09:00:00 Hits : 815
There are all kinds of faucets in sanitary ware, such as bathroom faucet, washing machine faucet, constant temperature faucet, etc. Many families have a headache when installing these faucets. It's too expensive to ask the master, and they can't install them themselves.
In fact, the faucet will be installed when you master the method. Today, Xiaobian will tell you the installation methods of all kinds of faucets. You don't have to worry about how to install the faucet in the future!
I General faucet installation
1. Pay attention to the protection of the faucet coating to prevent other metal objects from damaging the faucet coating
2. During installation, the hot and cold water pipes of the faucet shall be tightened with force, and the faucet easy to install device shall be tightened with force at the same time
3. For the installation of the washer, since the washer plays a great role in protecting the faucet, you must not forget to place the washer
4. Place the faucet to be installed on the reserved installation port, install the sleeve, and tighten it with the greatest strength
5. After installation, open the faucet, drain the water with the largest valve, remove the sludge and sundries in the pipeline, and clean the water pipe.
II Installation steps of bathroom basin faucet
1. First of all, when we buy the faucet, we will find some basic parts below;
2. First, we put the copper buckle and a rubber pad into the two hoses;
3. Then put one end of the two pipes through the hole of the washbasin;
4. First put the rubber pad into the hose, and then put the copper wire into it;
5. Take the faucet and screw the screw port of the pipe on the faucet;
6. Screw the copper wire on the faucet and put it into the hole of the porcelain basin to fix the faucet.
Tips: during installation, the special angle valve must be selected, and the angle valve must be fixed with the cold and hot water pipe of the wall outlet. If the inlet pipe is too int, it can be cut off, but do not bend hard to 90 degrees or greater. When installing the basin to remove water, please don't forget to buy the small interface of the faucet.
III Installation steps of kitchen faucet
1. Remove the whole accessories of the faucet (dental tube, rubber gasket, stainless steel gasket and fixing nut);
2. Pass one of the water inlet pipes through the opening of the faucet and through the table;
3. Screw the penetrated water inlet pipe into the water inlet hole under the faucet and tighten it properly;
4. Pass the whole tooth pipe removed through the water inlet pipe screwed into the tap water inlet;
5. Pass the second water inlet pipe through the whole tooth pipe and screw it into another water inlet under the faucet and tighten it properly;
6. Align the dental tube with the bottom of the faucet and tighten it properly, adjust the position of the faucet, and then fix and tighten the accessories properly.
IV Precautions for installation of thermostatic faucet
1. Users with small solid lumps in tap water are not suitable to use thermostatic faucets;
2. If the tap water contains powdery sediment or soft foreign matters, it may reduce the sensitivity of the thermostatic valve core and shorten the service life of the thermostatic faucet;
3. Try to shorten the distance between the water heater and the faucet so that the hot water can reach the faucet as soon as possible;
4. The normal operating water pressure is 0.05Mpa ~ 0.6MPa;
5. The hot and cold water supply pipe must not be installed incorrectly. The hot water pipe must be on the left and the cold water pipe must be on the right;
6. Be sure to clean the installation site before installing the thermostatic faucet, so as not to damage the rubber ring, thread, thermostatic valve core and other parts of the faucet;
7. Please install according to the instructions in the manual, and pay special attention not to miss, lose or damage any gaskets or rubber rings;
8. The thermostatic faucet itself has no heating function. Please adjust the water temperature of the water heater to 60 ℃ ~ 85 ℃;
9. The shower and shower pipe cannot withstand high temperature above 60 ℃;
10. After each use, be sure to adjust the water temperature adjustment knob on the left to below 40 ℃;
11. If the water pressure difference between hot water and cold water is too large, please use a screwdriver to adjust the valve of the support. Families using gas water heaters need to pay more attention to this.
V Precautions for installation of induction faucet
1. When installing this kind of faucet, make sure that its sensing window is facing down and the distance from the basin bottom of the washing table is at least 25cm, otherwise its sensing sensitivity will be affected.
2. Turn off the water source at the water inlet where the induction faucet is to be installed to ensure the installation of the faucet.
3. Take out the faucet body of the faucet from the package, wrap the water inlet thread on the faucet body with raw material tape or leak proof glue, and screw the faucet body into the fixed position where the water inlet pipe is to be installed on the wall.
4. Remove the battery box cover at the protruding part of the top cover above the induction faucet body, carefully pull out the battery box inside, and put four new No. 3 alkaline batteries into the positive and negative poles of the battery according to the instructions. At this time, the red light of the sensing window on the faucet body will flicker continuously. After the red light of the sensing window on the faucet body stops flashing, push it into the battery box and lock it. In this way, the faucet body is installed.
5. Open the water source at the water inlet where the faucet is to be installed for test, and adjust the water output with the water valve button. If there is no problem, it can be put into use.
Tips: in home decoration, in addition to the general decoration, the most important thing is the decoration of hardware and small parts, and the faucet beints to one of them. The installation of faucet directly affects people's health.
Therefore, whether it is a bathroom faucet, a kitchen faucet or a washing machine faucet, the installation process must follow the rules and be more careful. I hope you can have a certain understanding of the installation of the faucet after reading the introduction of this article.
3. The plastic protective cover of the valve core shall not be removed easily during embedding, so as to avoid damage to the valve core by cement and other chores during embedding
4. In addition, when embedding the valve core, pay attention to the up, down, left and right directions of the valve core to avoid wrong embedding of the valve core
5. If there is a deviation in the size of the embedded water inlet pipe of the wall mounted faucet, the adjustable abductor can be used to calibrate the position.
Tips: when you buy Shower, bathtub and wall faucet, you can choose the appropriate height to bury the outlet pipe. The distance between hot and cold water pipes must reach 15 cm. Before installation, you must not forget to flush the water pipe to avoid damage to the faucet due to the hard water quality.
VII Installation steps of washing machine faucet
Tips: the sealing ring of inlet filter and connector shall be installed well, and the tightening force shall not be too large to avoid damaging the thread. The water supply pressure shall be between 30KPa and 1000kPa. If it exceeds the range, the pressure reducing or pressurizing device shall be used. After installation, it shall be carefully checked to avoid water leakage.
In fact, the faucet will be installed when you master the method. Today, Xiaobian will tell you the installation methods of all kinds of faucets. You don't have to worry about how to install the faucet in the future!
I General faucet installation
1. Pay attention to the protection of the faucet coating to prevent other metal objects from damaging the faucet coating
2. During installation, the hot and cold water pipes of the faucet shall be tightened with force, and the faucet easy to install device shall be tightened with force at the same time
3. For the installation of the washer, since the washer plays a great role in protecting the faucet, you must not forget to place the washer
4. Place the faucet to be installed on the reserved installation port, install the sleeve, and tighten it with the greatest strength
5. After installation, open the faucet, drain the water with the largest valve, remove the sludge and sundries in the pipeline, and clean the water pipe.
II Installation steps of bathroom basin faucet
1. First of all, when we buy the faucet, we will find some basic parts below;
2. First, we put the copper buckle and a rubber pad into the two hoses;
3. Then put one end of the two pipes through the hole of the washbasin;
4. First put the rubber pad into the hose, and then put the copper wire into it;
5. Take the faucet and screw the screw port of the pipe on the faucet;
6. Screw the copper wire on the faucet and put it into the hole of the porcelain basin to fix the faucet.
Tips: during installation, the special angle valve must be selected, and the angle valve must be fixed with the cold and hot water pipe of the wall outlet. If the inlet pipe is too int, it can be cut off, but do not bend hard to 90 degrees or greater. When installing the basin to remove water, please don't forget to buy the small interface of the faucet.
III Installation steps of kitchen faucet
1. Remove the whole accessories of the faucet (dental tube, rubber gasket, stainless steel gasket and fixing nut);
2. Pass one of the water inlet pipes through the opening of the faucet and through the table;
3. Screw the penetrated water inlet pipe into the water inlet hole under the faucet and tighten it properly;
4. Pass the whole tooth pipe removed through the water inlet pipe screwed into the tap water inlet;
5. Pass the second water inlet pipe through the whole tooth pipe and screw it into another water inlet under the faucet and tighten it properly;
6. Align the dental tube with the bottom of the faucet and tighten it properly, adjust the position of the faucet, and then fix and tighten the accessories properly.
IV Precautions for installation of thermostatic faucet
1. Users with small solid lumps in tap water are not suitable to use thermostatic faucets;
2. If the tap water contains powdery sediment or soft foreign matters, it may reduce the sensitivity of the thermostatic valve core and shorten the service life of the thermostatic faucet;
3. Try to shorten the distance between the water heater and the faucet so that the hot water can reach the faucet as soon as possible;
4. The normal operating water pressure is 0.05Mpa ~ 0.6MPa;
5. The hot and cold water supply pipe must not be installed incorrectly. The hot water pipe must be on the left and the cold water pipe must be on the right;
6. Be sure to clean the installation site before installing the thermostatic faucet, so as not to damage the rubber ring, thread, thermostatic valve core and other parts of the faucet;
7. Please install according to the instructions in the manual, and pay special attention not to miss, lose or damage any gaskets or rubber rings;
8. The thermostatic faucet itself has no heating function. Please adjust the water temperature of the water heater to 60 ℃ ~ 85 ℃;
9. The shower and shower pipe cannot withstand high temperature above 60 ℃;
10. After each use, be sure to adjust the water temperature adjustment knob on the left to below 40 ℃;
11. If the water pressure difference between hot water and cold water is too large, please use a screwdriver to adjust the valve of the support. Families using gas water heaters need to pay more attention to this.
V Precautions for installation of induction faucet
1. When installing this kind of faucet, make sure that its sensing window is facing down and the distance from the basin bottom of the washing table is at least 25cm, otherwise its sensing sensitivity will be affected.
2. Turn off the water source at the water inlet where the induction faucet is to be installed to ensure the installation of the faucet.
3. Take out the faucet body of the faucet from the package, wrap the water inlet thread on the faucet body with raw material tape or leak proof glue, and screw the faucet body into the fixed position where the water inlet pipe is to be installed on the wall.
4. Remove the battery box cover at the protruding part of the top cover above the induction faucet body, carefully pull out the battery box inside, and put four new No. 3 alkaline batteries into the positive and negative poles of the battery according to the instructions. At this time, the red light of the sensing window on the faucet body will flicker continuously. After the red light of the sensing window on the faucet body stops flashing, push it into the battery box and lock it. In this way, the faucet body is installed.
5. Open the water source at the water inlet where the faucet is to be installed for test, and adjust the water output with the water valve button. If there is no problem, it can be put into use.
Tips: in home decoration, in addition to the general decoration, the most important thing is the decoration of hardware and small parts, and the faucet beints to one of them. The installation of faucet directly affects people's health.
Therefore, whether it is a bathroom faucet, a kitchen faucet or a washing machine faucet, the installation process must follow the rules and be more careful. I hope you can have a certain understanding of the installation of the faucet after reading the introduction of this article.
Vi Installation of shower and bathtub faucet (wall hanging)
1. After purchasing the concealed faucet, the valve core of the faucet shall be embedded in the wall
3. The plastic protective cover of the valve core shall not be removed easily during embedding, so as to avoid damage to the valve core by cement and other chores during embedding
4. In addition, when embedding the valve core, pay attention to the up, down, left and right directions of the valve core to avoid wrong embedding of the valve core
5. If there is a deviation in the size of the embedded water inlet pipe of the wall mounted faucet, the adjustable abductor can be used to calibrate the position.
Tips: when you buy Shower, bathtub and wall faucet, you can choose the appropriate height to bury the outlet pipe. The distance between hot and cold water pipes must reach 15 cm. Before installation, you must not forget to flush the water pipe to avoid damage to the faucet due to the hard water quality.
VII Installation steps of washing machine faucet
Tips: the sealing ring of inlet filter and connector shall be installed well, and the tightening force shall not be too large to avoid damaging the thread. The water supply pressure shall be between 30KPa and 1000kPa. If it exceeds the range, the pressure reducing or pressurizing device shall be used. After installation, it shall be carefully checked to avoid water leakage.
